Infrared thermographic evaluation of large composite grid parts subjected to axial loading

Many composite parts, such as laminated panels and grid-like shells, operate under high mechanical loading. Evaluation of their structural integrity is crucial to ensure the long-lasting operation of critical components. Since testing a structure under full or “proof” load might be dangerous for personnel, it would be preferable to use a remote, rapid inspection technique. This paper describes a practical application of IR thermography to the inspection of large composite parts used in the aerospace industry. This work has used just one cycle of increasing load from zero load to failure, and this was done for both for tensile and compressive loads. It is shown that, during the formation of micro-defects in polymeric composites, about 40 % of the total dissipated energy is expended for material heating, while about 60 % is related to material damage accompanied by an increase in the defect concentration. Non-uniform composite deformation causes temperature anomalies, whose amplitude may reach 1.5–2.5 °C at a load of about 50–60 % of the limit load.     

Surface strain-field determination of tympanic membrane using 3D-digital holographic interferometry

In order to increase the understanding of soft tissues mechanical properties, 3D Digital Holographic Interferometry (3D-DHI) was used to quantify the strain-field on a cat tympanic membrane (TM) surface. The experiments were carried out applying a constant sound-stimuli pressure of 90 dB SPL (0.632 Pa) on the TM at 1.2 kHz. The technique allows the accurate acquisition of the micro-displacement data along the x, y and z directions, which is a must for a full characterization of the tissue mechanical behavior under load, and for the calculation of the strain-field in situ. The displacements repeatability in z direction shows a standard deviation of 0.062 µm at 95% confidence level. In order to realize the full 3D characterization correctly the contour of the TM surface was measured employing the optically non-contact two-illumination positions contouring method. The x, y and z displacements combined with the TM contour data allow the evaluation its strain-field by spatially differentiating the u(m,n), v(m,n), and w(m,n) deformation components. The accurate and correct determination of the TM strain-field leads to describing its elasticity, which is an important parameter needed to improve ear biomechanics studies, audition processes and TM mobility in both experimental measurements and theoretical analysis of ear functionality and its modeling.     

基于超声波和云测试的油井液面测试系统研究

针对目前油井液面深度测试系统测量范围小、误差大、稳定性低的缺点,提出了基于声波法测动液面原理,利用时间序列分析技术、新息自适应卡尔曼滤波技术来实时检测回波信号,进而实现对油井液面深度的高精度测量和噪声处理;选用FPGA和云测试技术成功实现了油井液面深度测量系统的远程化和网络化。基于云测试的油井液面远程监测系统目前已在油田生产现场通过测试,测试结果表明,系统稳定,算法实时、高效,动液面深度测量误差小,测量精度高,能满足实际工程应用。     

一种新的珍珠层厚度测量方法

珍珠层厚度是是珍珠价值最主要的衡量指标之一,目前珍珠层厚度的无损测量方法主要采用光学相干层析成像技术和X射线技术。光学相干层析成像技术在实际测量时精度较低。在研究X射线测量原理的基础上,提出了一种新的珠层厚度测量方法。首先介绍了灰度图像的边缘识别算法和珍珠核、珍珠外圆度拟合算法,其次提出了一种引入对照机制的珍珠层测量算法,最后还对算法的误差进行了分析,算法的误差可以控制在0.02%以内。实际的测量也验证了本测量方法具有很高的精度。     

嵌入式软件GUI自动化测试平台研究

为实现嵌入式软件的GUI自动化测试,本文对嵌入式软件GUI自动化测试现状深入分析,提出了一种无侵入式的GUI自动化测试框架,利用图像采集与信息识别技术实现测试用例结果判断;利用键盘鼠标模拟技术模拟测试用例执行的人机交互;利用脚本语言嵌入技术实现用例编辑与转换、利用嵌入式软件GUI测试自动化控制技术实现用例的自动驱动与执行。在此基础上,设计并研发了嵌入式软件GUI自动化测试平台,能够方便、有效的实现无侵入式的嵌入式GUI自动化测试。     

基于单神经元PID控制器的压电陶瓷控制方法

卫星地面综合测试是卫星研制过程中的重要环节,对系统功能验证及性能评估具有重要作用。传统的卫星地面综合测试系统存在研制周期长、投入较大、自动化流程不够完整、可重用性较差等不足。而北斗导航卫星地面综合测试系统采用分布式、高实时性、可配置、多主机的集成体系结构,是集计算机通讯、实时控制、实时数据处理、事后分析等功能于一体的测试系统,适用于从卫星总装集成到发射各个阶段的电气测试。通过卫星系统级的各项接口、功能、性能指标测试,表明该系统满足支持系统论证、状态确认、问题排查等测试需求,有力支撑了北斗导航卫星的成功发射和在轨运行。     

基于ARM的嵌入式超声传播时间测量装置

应用超声波检测技术进行检测时,通常需对超声波在介质中的传播时间进行精准的测量,为精准测量超声波的传播时间,设计了一套基于ARM的嵌入式超声传播时间测量装置。该装置电路运行稳定,成本低廉,采用多次测量结果取算数平均值的方法以减小随机干扰,采用参比方法放置接收探头以消减电路中电子器件的延时。通过对实验结果进行分析,得出该装置可精准测量超声波在实验试块中的传播时间且满足设计要求,分辨率可达一纳秒。     

强夯处理红粘土沉降试验研究

红粘土作为高填方体的底层地基,处理其沉降和不均匀性沉降是高填方工程研究的重点。以某机场红粘土高填地基的处理为例,通过沉降分析和方案比选开展强夯处理试验研究。根据场区内不同覆土厚度,采用不同能级进行强夯处理试验确定了合理的施工工艺和参数。通过施工中沉降观测,施工后地基土的物理力学指标试验、载荷试验和工后沉降观测,强夯处理取得了良好的效果,满足设计要求。指导大面积施工时,在质量、造价、工期上都取得了成功。     

LaPO_4∶Ce,Tb纳米荧光粉末的合成及其在指纹无损显现中的应用

采用溶剂热法在水和乙二醇的混合溶剂中合成出了高质量的LaPO_4∶Ce,Tb纳米荧光粉末。然后通过透射电子显微镜(TEM)、粉末X射线衍射(XRD)、荧光光谱(FS)等表征手段分别对稀土纳米荧光粉末的微观形貌、晶体类型、荧光性能进行了表征,合成纳米荧光粉末的形貌为单分散的纳米棒,平均长度为700nm、平均直径为20nm,其晶体结构为单斜LaPO_4晶型,并且在254nm紫外光照射下能够产生较强的绿色荧光。最后将合成的纳米荧光粉末应用于光滑客体表面汗潜指纹的无损显现中,并详细考察了指纹显现的对比度、灵敏度、选择性、背景干扰等指标。实验结果表明,使用LaPO_4∶Ce,Tb纳米荧光粉末显现的指纹在254nm紫外光的激发下能够产生明亮的绿色荧光,指纹乳突纹线部位连贯清晰、细微特征反映明显,指纹与客体之间的对比反差强烈、客体产生的背景干扰较小,因此该显现方法具有较高的对比度、灵敏度和选择性。本显现方法具有操作方法简单、显现效果优良、适用范围广泛等优点。本研究的重要创新之处在于,经LaPO_4∶Ce,Tb纳米荧光粉末显现后的指纹还可以进行后续的DNA提取及检测,这是传统的指纹显现粉末所不能及的。本研究为指纹物证和生物物证这两大物证的同时利用提供了有益参考。     

Nondestructive evaluation for remanent life of modified 9Cr-1Mo steel by reversible magnetic permeability

We present a magnetic and nondestructive method to evaluate the remanent life of modified 9Cr-1Mo steel by measuring the reversible magnetic permeability. Specimens with ten different kinds of aging periods were prepared using an isothermal heat treatment at 690 °C. The Larson-Miller parameter (LMP) was calculated and the peak interval of reversible magnetic permeability (PIRMP) was measured using the surface type probe. PIRMP was inversely proportional to LMP. We can evaluate the remanent life of modified 9Cr-1Mo steel using the relationship between PIRMP and LMP. Also, we present the possibility that the tensile strength and yield strength measured by destructive methods could be estimated by PIRMP measured nondestructively.